Rising Damp Treatment

Guide · Owners of period homes · 4 min read · Updated 17 November 2026

Rising Damp in Old Houses: A Breathable Approach

Short answer

In older solid-walled houses, damp at the base of walls is often caused by modern materials trapping moisture, such as cement render, gypsum plaster, plastic paint and raised ground levels. The best approach usually starts with restoring breathability and drainage: lowering ground, installing French drains at £80–£150 per metre and replastering in lime at £70–£130 per m², with chemical treatment considered only if testing still justifies it.

Rising Damp in Old Houses: A Breathable Approach

How old walls manage moisture

Houses built before the early twentieth century were usually constructed with solid walls of brick or stone, bedded in lime mortar and finished with lime plaster and limewash or distemper. These materials absorb moisture and release it again. Rain soaks into the outer face and dries out. Ground moisture rises a little way and evaporates. As long as the wall can breathe, it stays in balance.

Many period homes were built without a damp course, or with slate DPCs that have since cracked. Some have stood dry for well over a century. The problems tend to start when that balance is disturbed.

What usually goes wrong

Over the decades, older houses often gain features that trap moisture. Cement render and cement pointing replace lime on the outside. Gypsum plaster and vinyl paint replace lime plaster inside. Patios and paths are laid higher against the walls. Suspended timber floors are replaced with concrete slabs that push moisture into the wall base. Each change reduces the wall's ability to dry, so moisture accumulates and appears as damp.

These changes were usually made with good intentions, often to make the house look neater or feel more modern. But they tend to work against the original construction rather than with it. The resulting damp is then misread as rising damp from a failed or missing DPC, and the wall is injected, tanked and replastered in cement, which can make the underlying problem worse.

  • Cement render or pointing over soft brick or stone
  • Gypsum plaster and vinyl or plastic paints inside
  • External ground raised above the original floor level
  • Concrete floors replacing ventilated timber floors
  • Blocked air bricks under remaining timber floors
  • Leaking gutters and downpipes soaking the wall base

A breathable repair strategy

The first step is to remove the things that trap water and to keep water away from the wall. Lower outside ground levels where possible. Install a French drain, a gravel-filled trench with drainage along the wall base, to carry water away. Repair gutters and downpipes. Clear and reinstate air bricks.

Inside, remove gypsum plaster and modern paint from the lower walls and replace them with lime plaster and breathable finishes. Lime allows moisture and salts to evaporate rather than building up behind a hard skin. The improvement can take months to show as the wall dries out, but it addresses the cause rather than covering it.

Repointing with lime mortar where cement pointing has failed is another valuable step. Cement joints that are harder than the surrounding brick force moisture to escape through the brick face, which can lead to spalling and keeps the wall wetter than it should be. Lime pointing lets the joints act as the wall's drying route again.

MeasurePurposeTypical price
French drain at wall baseLowers ground moisture against the wall£80–£150 per metre
Lime replasteringLets the wall breathe and salts evaporate£70–£130 per m²
Joist end and floor repairsReplaces timber decayed by damp masonryfrom £350
Single wall injection and replasterOnly if testing confirms persistent rising damp£500–£1,200

When chemical treatment is still justified

Breathable repairs solve many problems on their own, but not all. Where carbide testing and salt analysis show that moisture is still rising strongly after drainage and breathability have been improved, a damp barrier may be needed. In brick walls with regular mortar courses, injection is often possible. In random rubble stone walls without continuous joints, chemical barriers are much less effective and may not be suitable.

If a barrier is installed, it should be combined with lime or another breathable plaster system appropriate to the wall, rather than an impermeable finish that will simply move the moisture problem elsewhere.

Agree in advance how success will be measured. Repeat carbide tests a season or two after the breathable repairs give a clear comparison with the original readings and show whether further work is genuinely needed.

Listed buildings and conservation areas

If your home is listed, listed building consent is normally needed for damp treatment that affects its character, such as removing historic plaster or drilling a new damp barrier. This comes from the Planning (Listed Buildings and Conservation Areas) Act 1990, and doing such work without consent can be a criminal offence. Speak to your local conservation officer early. They will often support breathable repairs and drainage improvements and may expect evidence before agreeing to chemical treatment.

Even in unlisted period homes, choosing contractors familiar with traditional buildings makes a significant difference to the outcome.

Living with an old house

Solid walls in old houses are rarely bone dry, and they do not need to be. A little seasonal moisture at the wall base is normal and harmless if the wall can dry out. Keep gutters clear, avoid storing items against damp walls, heat the house steadily rather than in short bursts and keep rooms ventilated. Use breathable paints such as limewash or mineral paints on lime plaster. With the right materials, many period houses stay dry for generations.

When you need work done, look for builders and plasterers who regularly work with lime and understand traditional construction. Ask to see examples of similar jobs and how they dealt with moisture.

Questions people also ask

Should I inject a damp proof course into a Victorian house?

Only if testing shows genuine rising damp after other causes have been dealt with. Many Victorian houses suffer damp because of cement render, gypsum plaster, raised ground or leaking gutters. Fixing these first often solves the problem. If injection is still needed, combine it with a suitable plaster system rather than an impermeable finish.

Is lime plaster better for damp walls?

On solid-walled period properties, lime plaster is usually the better choice because it lets moisture and salts evaporate instead of trapping them. It takes longer to apply and cure, and it costs more than gypsum. On many modern cavity-walled homes, cement-based salt-resistant plasters are more commonly used after treatment.

Can cement render cause damp in old houses?

Yes. Hard cement render traps moisture in soft brick and stone walls. Water gets in through hairline cracks but cannot escape easily, so the wall stays wet, often showing damp at the base inside. Replacing cement render with lime render is a common and effective repair on period homes.

Written and checked by the Rising Damp Treatment team. Read our editorial policy.

Get a free rising damp treatment quote

Tell us what you need and we'll come back with a clear price.

Request a quote