Guide · Homeowners · 3 min read · Updated 17 November 2026
Preparing for Rising Damp Treatment: Checklist and Timeline
Short answer
Before rising damp treatment, clear furniture at least a metre from affected walls, lift carpets, empty fitted cupboards and arrange for sockets and radiators to be disconnected. A single wall typically takes one to two days and a full room around three to five days, plus drying time. Afterwards, use breathable paint, ventilate well and avoid hanging wallpaper until the wall has dried.
Before the team arrives
Rising damp treatment is messy. Plaster has to be hacked off, holes drilled and new plaster applied, all of which create dust and debris. A little preparation protects your belongings and helps the team work faster, which can save time on site. Agree with the contractor exactly which jobs they will handle and which you will do yourself.
Ask how they will protect floors and doorways, where they will mix plaster and how waste will be removed. If any electrical sockets or radiators are on affected walls, confirm who will disconnect them and whether a separate electrician or plumber is needed.
Take photos of the affected walls before work starts. They provide a useful record for any future guarantee claim and help show buyers what was done.
- Move furniture at least a metre away from affected walls
- Lift carpets and underlay along treated walls
- Empty and, if needed, remove fitted cupboards and shelving
- Take down pictures, curtains and wall-mounted TVs
- Arrange disconnection of radiators and sockets
- Seal off nearby rooms and cover belongings against dust
What happens each day
Work usually starts by removing skirting boards and stripping plaster to the agreed height, typically at least a metre. The bare wall is inspected, and any rotten timber grounds, joist ends or wall plates are noted. Holes are then drilled into the chosen mortar bed for a chemical barrier, and cream is injected into each hole before the holes are made good.
Next comes replastering. A salt-resistant cement-based system or lime plaster is applied in coats, with drying time between them. Lime may require several visits over a longer period. Finally new skirting boards are fitted, and sockets and radiators are refitted once it is safe to do so.
Typical timescales
How long the job takes depends on the size of the area and the plaster system used. The table gives typical timescales for the work on site. Drying before full decoration takes longer and varies with wall thickness and conditions.
The contractor should give you a written programme showing when each room will be out of use. If you are working around family routines or a planned move, raise it early so the work can be phased to suit.
| Job | Time on site | Notes |
|---|---|---|
| Single wall | 1–2 days | Strip, inject, replaster and refit skirting |
| Full room | 3–5 days | Several walls, depending on access |
| Ground floor of a terraced house | 1–2 weeks | Several rooms, often in stages |
| Lime replastering | Longer | Multiple coats with curing time between them |
| Joist or floor repairs | Extra 1–2 days | Depends on how much timber is affected |
Living in the house during treatment
Most people stay at home during rising damp treatment. Expect noise from drilling and plaster removal, and dust despite protective sheeting. Kitchens are the most disruptive rooms to treat, because units and appliances may have to be removed. If the kitchen is affected, plan simple meals and set up a temporary space elsewhere for a few days.
Keep children and pets away from the work area. Silane-based damp-proofing creams have low odour compared with older solvent-based fluids, but ventilate the room during and after injection and follow any guidance the installer gives from the product safety data sheet.
If anyone in the household has respiratory problems, mention it to the contractor so they can take extra care with dust control and ventilation.
After the treatment
Walls need time to dry out completely, which can take months for thick masonry. A commonly used rule of thumb is around a month for each 25 mm of wall thickness. During this time, use a breathable emulsion and avoid vinyl paint, wallpaper and tiling on treated walls unless the plaster system allows it. Leave a gap behind furniture and keep rooms gently heated and well ventilated.
White salt crystals may appear on the surface as the wall dries. Brush them off with a dry brush. Do not wash them, because that dissolves the salts and puts them back into the wall.
If the original cause was partly bridging or a leak, make sure those external fixes stay in place. A new patio or flower bed laid against the wall in future can undo the treatment.
Paperwork to keep
Keep the original survey, the quote, the invoice and any guarantee in a safe place. Note the date of completion and the areas treated. If damp reappears, you will need these to make a claim, and they will be requested by a buyer's solicitor when you sell. If the guarantee is insurance-backed, keep the policy document with it. Photos of the wall before, during and after treatment are a useful extra record of what was done.
If you sell within the guarantee period, check whether the guarantee can be transferred to the new owner. Most can, but some require notification or a small fee, and buyers will value a transferable guarantee.
It is also worth noting any maintenance you carry out afterwards, such as clearing gutters or lowering ground levels, since some guarantees require the property to be kept in reasonable repair.
Questions people also ask
Can I stay in my house during damp proofing?
Yes, most people do. Expect dust, drilling noise and some disruption, especially in kitchens. Close doors to other rooms and cover belongings. Ventilate the treated room during injection and keep children and pets out of the work area until the team has finished for the day.
How soon can I put furniture back after treatment?
Furniture can usually go back once the new plaster has set and skirting boards are refitted, but leave a small gap between large items and the treated wall. This lets air circulate while the wall continues to dry. Avoid fixing heavy units to the new plaster until the installer confirms it is ready.
Why have white crystals appeared after treatment?
These are usually salts being carried to the surface as the wall dries out, known as efflorescence. They are normal in the months after treatment. Brush them away with a dry brush rather than washing them off. If they keep appearing in large amounts after many months, ask the installer to inspect.
Written and checked by the Rising Damp Treatment team. Read our editorial policy.
More guides
How Much Does Rising Damp Treatment Cost in the UK?
Rising damp treatment in the UK costs £500–£1,200 for a single internal wall with replastering, £1,200–£2,800 for a full room and £2,500–£6,000 for…
Rising Damp or Condensation? How to Tell the Difference
Rising damp appears as a band of dampness at the base of walls, usually up to about a metre high, with a tide mark, salt crystals, crumbling plaster…
Replastering After Rising Damp Treatment: What You Need to Know
After rising damp treatment, salt-contaminated plaster is usually stripped to at least one metre and replaced with a salt-resistant or breathable…
Rising Damp in Old Houses: A Breathable Approach
In older solid-walled houses, damp at the base of walls is often caused by modern materials trapping moisture, such as cement render, gypsum plaster,…
Get a free rising damp treatment quote
Tell us what you need and we'll come back with a clear price.
Request a quote