Guide · Homeowners · 4 min read · Updated 17 November 2026
Replastering After Rising Damp Treatment: What You Need to Know
Short answer
After rising damp treatment, salt-contaminated plaster is usually stripped to at least one metre and replaced with a salt-resistant or breathable lime system. Without this, ground salts in the old plaster keep drawing moisture from the air and the wall stays damp. Lime replastering costs £70–£130 per m². Walls then need time to dry, and the first decoration should be breathable emulsion.
Why replastering is part of the treatment
When groundwater rises through a wall and evaporates from the surface, it leaves salts behind in the plaster. Chlorides and nitrates in particular are hygroscopic, which means they absorb moisture from the air. Even once a new damp course has stopped water rising from below, salt-laden plaster will keep pulling moisture in whenever the room is humid. The wall looks and feels damp, and paint and paper keep failing.
Replacing the contaminated plaster removes the salts and gives the wall a fresh surface designed to cope with the drying process. BS 6576, the code of practice for chemical damp-proof courses, covers the replastering that should follow injection for this reason.
How high should plaster be removed?
The usual approach is to strip plaster to at least one metre above floor level, or to around 300 mm above the highest visible sign of damp or salts if that is higher. Stopping short leaves salts in place and the tide mark often reappears just above the new plaster. Plaster is removed back to the bare masonry, and loose mortar joints are raked out.
Skirting boards come off at the same time. Timber grounds and fixings behind them are checked for rot, and any decayed timber is replaced with treated wood. This is also the moment to check floor joists and wall plates where they meet the damp wall.
Electrical back boxes and pipe runs inside the stripped area should be checked at this stage too, as metal boxes can corrode in damp walls.
- Strip to at least 1 m or 300 mm above the highest damp sign
- Remove back to bare masonry and rake out loose joints
- Take off skirtings and check timber grounds for rot
- Inspect joist ends and wall plates at the same time
- Remove all debris before plastering begins
Salt-resistant plaster or lime?
There are two main approaches. Cement-based salt-resistant systems, often a sand and cement render with a waterproofing or salt-retarding additive followed by a finish coat, hold salts back in the wall and give a hard, quick-drying surface. They suit many twentieth-century brick houses and are generally faster and cheaper.
Lime plaster takes the opposite approach. It is breathable, so moisture and salts can move through it and evaporate. This suits solid-walled Victorian and older properties, which were designed to manage moisture by letting it escape. Lime needs several coats, longer curing and careful protection from drying out too quickly, which is reflected in its price of £70 to £130 per m².
| Factor | Cement-based salt-resistant | Lime plaster |
|---|---|---|
| How it works | Holds moisture and salts back in the wall | Lets moisture and salts move and evaporate |
| Best suited to | Many post-1920 brick homes | Solid-walled, period and listed buildings |
| Drying before decoration | Usually quicker | Longer, several coats and curing time |
| Finish | Hard, smooth | Softer, slightly flexible |
| Typical price | Usually lower | £70–£130 per m² |
Why gypsum plaster should be avoided
Standard gypsum plasters, the pink-finish products used in most modern homes, are not suitable for walls that have had rising damp. Gypsum is sensitive to moisture and salts, and it will soften, crumble and stain if the wall behind it is still drying out. Many failed damp jobs are simply walls that were replastered in gypsum before they were dry.
If you are doing part of the work yourself or managing separate trades, make sure the plasterer knows the wall has been treated for rising damp and uses the system specified in the survey or treatment report.
Some specialists also use proprietary renovating plasters, which are lightweight and porous so that salts crystallise inside the plaster rather than on its surface. Whichever system is chosen, the plasterer should follow the manufacturer's application instructions exactly, including mix ratios, coat thickness and drying times between coats.
Drying times and decoration
Walls take a long time to dry. A commonly used rule of thumb is about a month for every 25 mm of wall thickness, so a solid brick wall can take many months to dry fully. The new plaster is designed to cope with this, but your decoration needs to allow it too.
Apply a breathable emulsion first, often a thinned mist coat, rather than vinyl paint or wallpaper. Leave fitted furniture slightly away from the wall to let air circulate. Use heating gently and keep the room ventilated. Small areas of efflorescence may appear on the surface as the wall dries. These can be brushed off dry and are not a sign that the treatment has failed.
Signs the replastering has gone wrong
Watch for plaster that stays dark and damp, a tide mark reappearing above the new plaster line or paint blistering in a band along the wall. These can point to plaster that was not stripped high enough, the wrong plaster being used, or the original cause of the damp still being present. Contact the installer early if you see these signs, and keep photos and dates to support any guarantee claim.
Problems can also appear if the room has heavy condensation, because even the best plaster will look damp if water is forming on its surface. Check humidity before assuming the treatment itself is at fault.
Questions people also ask
Do I have to replaster after a damp proof course?
In most cases, yes. The old plaster is usually full of hygroscopic ground salts that keep absorbing moisture from the air even after the new damp course has stopped water rising. Without replastering, the wall often looks just as damp as before. Lightly affected walls can sometimes be left, but a surveyor should confirm this.
How long after replastering can I paint?
Follow the plaster manufacturer's guidance and your installer's advice. Cement-based salt-resistant systems are usually ready sooner than lime. In either case, use a breathable emulsion for the first few months so the wall can continue drying. Avoid vinyl paints and wallpaper until the wall has fully dried out.
Can I use plasterboard instead of wet plaster?
Some systems use dry-lining or membranes fixed to the wall, which can be quicker. These need careful detailing so moisture is not trapped and timber battens do not rot. On solid-walled older homes, breathable lime plaster is usually preferred. Use whatever system is specified for your wall in the treatment report.
Written and checked by the Rising Damp Treatment team. Read our editorial policy.
More guides
How Much Does Rising Damp Treatment Cost in the UK?
Rising damp treatment in the UK costs £500–£1,200 for a single internal wall with replastering, £1,200–£2,800 for a full room and £2,500–£6,000 for…
Rising Damp or Condensation? How to Tell the Difference
Rising damp appears as a band of dampness at the base of walls, usually up to about a metre high, with a tide mark, salt crystals, crumbling plaster…
Rising Damp in Old Houses: A Breathable Approach
In older solid-walled houses, damp at the base of walls is often caused by modern materials trapping moisture, such as cement render, gypsum plaster,…
Preparing for Rising Damp Treatment: Checklist and Timeline
Before rising damp treatment, clear furniture at least a metre from affected walls, lift carpets, empty fitted cupboards and arrange for sockets and…
Get a free rising damp treatment quote
Tell us what you need and we'll come back with a clear price.
Request a quote